Garage Door Repair Services › Torsion Spring Replacement
Torsion Spring Replacement in Arlington, TX
The torsion spring sits on a metal shaft above the door opening and stores mechanical energy to counterbalance the door's weight. When it breaks, the door becomes effectively immovable — your opener motor can't compensate for a missing spring. Most Arlington homes have a single torsion spring, though heavier or wider doors often use two.
Arlington Garage Door Pros provides torsion spring replacement for homeowners across Arlington, TX. Call for a free inspection and a written quote before any work begins.
When to Call
When You Need Torsion Spring Replacement
- You heard a loud bang from the garage and the door won't open
- The door opens a few inches then stops, even with a working opener
- You can see a visible gap or separation in the coil spring above the door
- The door feels extremely heavy when you try to lift it manually
- One side of the door rises faster than the other during operation
- Your spring has visible rust or corrosion and is approaching ten years old
How It Works
Our Process for Torsion Spring Replacement
- 1
Phone assessment
We ask about your door size, weight, and how it failed. This helps us arrive with the right spring gauge and cycle rating already loaded on the truck.
- 2
On-site inspection
We measure the door, check the existing spring dimensions, and look at the cable drums and end bearing plates before touching anything. A broken spring sometimes reveals a secondary problem.
- 3
Safe removal
Torsion springs are under high tension. We use winding bars and follow a specific unwinding sequence to release tension before removing hardware. No shortcuts here.
- 4
Spring installation and tensioning
We install the replacement spring, set the correct number of turns based on door weight, and secure all hardware. The turn count matters — too few or too many causes premature failure.
- 5
Balance test
We disconnect the opener and manually lift the door to mid-height. A properly balanced door holds position on its own. If it drifts, we adjust tension before reconnecting.
- 6
Full cycle test
We run the door through several complete cycles with the opener reconnected, checking for smooth travel, proper limit settings, and no unusual noise.
What's included
- Removal of the broken spring and any damaged hardware directly caused by the break
- Replacement spring sized and rated to match your specific door weight and width
- Lubrication of spring, cable drums, and bearing plates during installation
- Door balance test and tension adjustment until the door holds mid-position
- Opener reconnection and cycle testing before we leave
- Explanation of what failed and what to watch for going forward
What's not included
- Replacing cables that were damaged separately from the spring break — that's a separate service
- Opener repairs or reprogramming if the opener itself was damaged during the failure
- Painting or cosmetic work on the door panels or frame
Real Situations
Common Scenarios in Arlington
A homeowner in a 1990s Arlington subdivision hears a loud snap at 7am and their car is trapped inside the garage before work.
This is the most common call we get. We prioritize same-day service for trapped vehicles. We'll confirm the spring size by phone, arrive with likely replacements, and in most cases have the door operating within an hour of arrival.
A homeowner notices the door has been struggling for weeks and spots visible rust and a small crack forming in the spring coil.
A cracked spring is a spring about to break — we treat it as an active failure. We replace it before it goes completely, which avoids the more urgent trapped-car scenario. We also check the opposing spring if there are two, since matched springs tend to fail close together.
A property manager in Arlington's older Pantego-area rental stock finds a tenant reporting the door opens crooked and scrapes the frame.
Uneven travel usually points to one spring in a two-spring system having failed or lost tension. We inspect both springs, replace whichever has failed, and re-tension the system so both sides carry equal load.
Arlington Context
Why this matters in Arlington
Arlington's temperature swings — from freezing winters to summers above 105 degrees — put real stress on metal springs. Torsion springs expand and contract with every temperature cycle, which accelerates fatigue over time. Homes built in the 1980s and 1990s, which make up a large share of Arlington's housing stock, are now on their second or third spring generation, and many were never upgraded to higher cycle-rated hardware.
Straight Talk
About pricing & scope
Spring pricing varies based on wire gauge, inside diameter, and cycle life rating — a heavier door requires a heavier spring, which costs more. If we find damaged cable drums or a bent torsion bar when we arrive, fixing those adds to the scope. We'll tell you what we found before adding anything to the job.
What This Fixes
Problems We See in Arlington
More Garage Door Repair Services
Torsion Spring Replacement Near You