Garage Door Repair Services › Garage Door Spring Replacement
Garage Door Spring Replacement in Arlington, TX
Springs do the actual lifting work — your opener just moves the door along the path the springs make possible. When they wear out or break, the door becomes dangerously heavy and the opener strains trying to compensate. Replacing springs is a job that requires proper tools and calibration to get the tension right for your door's weight.
Arlington Garage Door Pros provides garage door spring replacement for homeowners across Arlington, TX. Call for a free inspection and a written quote before any work begins.
When to Call
When You Need Garage Door Spring Replacement
- You heard a loud bang from the garage and the door won't open now.
- The opener runs but the door barely moves or lifts unevenly.
- You can see a visible gap in the coil of a torsion spring above the door.
- The door falls faster than normal when you disconnect the opener and lower it by hand.
- One side of the door rises faster than the other during operation.
- Springs are visibly rusty or show kinks after years of daily use.
How It Works
Our Process for Garage Door Spring Replacement
- 1
Confirm spring type and door specs
Torsion springs mount above the door on a shaft. Extension springs run along the side tracks. We identify your system and measure door height, width, and weight to size the replacement correctly.
- 2
Release remaining tension safely
A damaged spring can still hold significant tension. We release it with winding bars — not improvised tools — before removing anything from the shaft.
- 3
Remove old springs and hardware
We pull the worn springs along with any corroded cable drums or worn center bearing plates if they need to go. We don't leave compromised hardware in place.
- 4
Install correctly sized replacement springs
Springs are matched to your door's actual weight. An undersized spring fails early. An oversized spring makes the door dangerous. Sizing matters more than brand.
- 5
Wind and tension to spec
We wind the springs to the correct turn count based on door height. Then we test balance by hand — the door should hold still at waist height when released.
- 6
Reconnect and test the full system
We reconnect the opener, run several full cycles, and verify the opener isn't straining. Force and limit settings often need adjustment after a spring change.
What's included
- Removal of old springs and disposal — we take them with us.
- Correctly sized replacement spring or springs installed and tensioned.
- Cable and drum inspection included with every spring replacement.
- Manual balance test before reconnecting the opener.
- Opener force setting adjustment after new springs are in place.
What's not included
- Cable replacement if cables are frayed — that's a separate line item we'll flag.
- Opener repair if the motor was damaged from running against a broken spring.
- Conversions from extension to torsion spring systems — that's a larger scope project.
Real Situations
Common Scenarios in Arlington
A homeowner in north Arlington woke up to a snapped torsion spring after leaving for work, trapping their car inside.
We can release the door manually to get the vehicle out first, then complete the spring replacement. We don't make you wait until the full job is done to access your car.
A homeowner replaced their spring themselves six months ago and the door is already struggling to lift again.
DIY spring replacements often use the wrong cycle rating or incorrect wind count. We assess the current spring, measure the door weight, and replace it with a properly spec'd spring wound to the right tension.
An older home in Arlington has two extension springs, and one snapped while the other looks original.
We replace both at the same time. Leaving a spring that's the same age as the broken one just means a second call in a few weeks. We explain the reasoning and let you decide.
Arlington Context
Why this matters in Arlington
Arlington's temperature swings — cold winters and extended summers above 95 degrees — accelerate metal fatigue in springs. Many homes here have two-car garages with heavier doors, which puts more stress on the spring system daily. Doors that were installed in the 1990s building boom are now well past the typical spring lifespan.
Straight Talk
About pricing & scope
Spring cost varies by door size, weight, and spring type — a double-car door needs more spring mass than a single. If cables or drums are also worn, we'll point that out separately and let you decide. Doing related hardware at the same time usually makes sense since the door is already down.
What This Fixes
Problems We See in Arlington
More Garage Door Repair Services
Garage Door Spring Replacement Near You